How many data select lines are required for selecting eight inputs?
- A1
- B2
- C3
- D4
2^3 = 8, so three select lines are needed.
MCQs, short and long questions from lecture 18.Lecture 18 ki MCQs, short aur long sawal.
7 MCQs · 6 short · 4 long questions · 7 MCQs from past papers7 MCQs · 6 short · 4 long sawal · 7 MCQs past papers se
How many data select lines are required for selecting eight inputs?
2^3 = 8, so three select lines are needed.
Using a multiplexer as a parallel to serial converter requires ___________ connected to the multiplexer
A counter drives the select lines so the parallel inputs are output one after another.
The main use of the Multiplexer is to
A multiplexer selects one of several inputs and sends it to one output.
Two 2-input, 4-bit multiplexers 74X157 can be connected to implement a ____ multiplexer.
With a common select line, two 4-bit units side by side switch two 8-bit inputs.
8-bit parallel data can be converted into serial data by using ________ multiplexer
An 8-to-1 multiplexer with a counter on its select lines outputs the 8 bits one at a time.
________ Dual, 4-input multiplexer can be connected to form a 16-input multiplexer.
A 16-input MUX needs four 4-input MUXes, which is two dual 4-input (74X153) chips.
A multiplexer circuit has ______ input(s) and ______ output(s).
A MUX selects one of many data inputs onto a single output.
No MCQs match this filter.Is filter mein koi MCQ nahi.
What is a multiplexer, what are its applications and how is expression simplification done using a multiplexer?
A multiplexer (data selector) has several data inputs, select inputs and one output; the binary value on the select lines routes one data input to the output (2^n inputs need n select lines). Applications: time-division multiplexing of several signals onto one line (e.g. telephone lines), routing register contents to an ALU, row/column address multiplexing for dynamic memory, parallel-to-serial conversion and implementing logic functions. To implement a function, apply the input variables to the select lines and connect each data input to 0 or 1 according to the truth table; with one variable fed to the data inputs (as 0, 1, X or X'), an n-variable function needs only a mux with n-1 select lines.
Draw the function table of a 2-input 4-bit multiplexer.
74x157: inputs G' (active-low enable), S (select), 4-bit inputs A and B, 4-bit output Y. G'=1: Y=0000 (disabled). G'=0, S=0: Y=A (1Y=1A ... 4Y=4A). G'=0, S=1: Y=B (1Y=1B ... 4Y=4B).
Write the uses of the multiplexer.
Routing the contents of one of several registers to an ALU input, time-division multiplexing of signals (e.g. telephone lines), multiplexing row and column addresses of dynamic memory, parallel-to-serial conversion and implementing logic functions.
Draw circuit diagram of 2-input 8-bit multiplexer?
A 2-input 8-bit multiplexer selects one of two 8-bit words A7-A0 and B7-B0 and passes it to outputs Y7-Y0. It is made of eight 2-to-1 multiplexers that share one select line S (and an enable G): for every bit i, Yi = S'Ai + SBi, built with an inverter on S, two AND gates and an OR gate. When S = 0 the outputs follow A; when S = 1 they follow B. In practice two 74x157 quad 2-input multiplexers with common select and enable lines form the 8-bit multiplexer.
2 input 4 bit multiplexer function table
For the 2-input 4-bit multiplexer (such as the 74x157) with enable G and select S: G = 1, S = X: all outputs 1Y to 4Y = 0. G = 0, S = 0: 1Y to 4Y = 1A to 4A. G = 0, S = 1: 1Y to 4Y = 1B to 4B.
Write down four uses of multiplexers.
1) Data selection/routing: choosing one of several input lines onto one output. 2) Parallel-to-serial conversion, with a counter driving the select lines. 3) Implementing (generating) logic functions: variables on select lines, 0/1 on data inputs. 4) Time-division multiplexing, sharing one line or display among several sources (e.g. multiplexed displays).
Implement f(A, B, C, D) = AC'D' + B'D using a 4-to-1 multiplexer. Choose the appropriate control inputs
f = Σm(1, 3, 8, 9, 11, 12). Use C and D as the select inputs (S1 = C, S0 = D). Then CD = 00 gives f = A, CD = 01 gives f = B', CD = 10 gives f = 0, CD = 11 gives f = B'. So connect I0 = A, I1 = B', I2 = 0, I3 = B'.
Draw the circuit diagram of the 4x1 Multiplexer. Also write down its truth table?
A 4x1 multiplexer has data inputs D0 to D3, select inputs S1 and S0 and one output Y. Truth table: S1=0, S0=0: Y = D0; S1=0, S0=1: Y = D1; S1=1, S0=0: Y = D2; S1=1, S0=1: Y = D3. Y = S1'S0'D0 + S1'S0D1 + S1S0'D2 + S1S0D3. Circuit: two inverters give S1' and S0'; four 3-input AND gates form the four product terms (each with one data input and the matching select combination); a 4-input OR gate combines the AND outputs into Y.
Explain 8-input Multiplexer with the help of circuit Diagram and Function Table.
An 8-input (8-to-1) multiplexer has data inputs D0 to D7, three select inputs C, B, A, an enable input and the output Y. Function table (enabled): CBA = 000: Y = D0; 001: Y = D1; 010: Y = D2; 011: Y = D3; 100: Y = D4; 101: Y = D5; 110: Y = D6; 111: Y = D7; when disabled Y = 0. Y = C'B'A'D0 + C'B'AD1 + C'BA'D2 + C'BAD3 + CB'A'D4 + CB'AD5 + CBA'D6 + CBAD7. Circuit: inverters give C', B', A'; eight 4-input AND gates (plus the enable) each combine one data input with its select combination; an 8-input OR gate combines them into Y. The 74x151 is such a multiplexer and also gives the complemented output.
Multiplexers can be used as a "Logic Function Generator". Draw only circuit diagram and function table based on three variables.
Use an 8-input (74X151) multiplexer. Connect the three variables A, B, C to the select lines S2, S1, S0. Tie each data input Di to logic 1 or 0 equal to the function value for minterm i, and enable the MUX. Function table: for ABC = 000 to 111 the MUX selects D0 to D7 in turn, so output Y = F(A,B,C) (Y = 1 exactly for the minterms whose Di is tied to 1).