The LSD test is applied only if the null hypothesis is:
- ARejected
- BAccepted
- CNo conclusion
- DAcknowledged
LSD is used to find which means differ, which is needed only after ANOVA rejects H0.
MCQs, short and long questions from lecture 44.Lecture 44 ki MCQs, short aur long sawal.
4 MCQs · 7 short · 4 long questions · 4 MCQs from past papers4 MCQs · 7 short · 4 long sawal · 4 MCQs past papers se
The LSD test is applied only if the null hypothesis is:
LSD is used to find which means differ, which is needed only after ANOVA rejects H0.
In the test of goodness of fit, the ________ is used as a test statistic.
The goodness-of-fit test uses χ² = Σ(o − e)²/e.
If there are 8 treatments with 6 blocks in a randomized completed block design then what are the degrees of freedom for treatments?
Treatment df = k − 1 = 8 − 1 = 7.
The LSD test is applied when the null hypothesis is:
The LSD test compares pairs of treatment means only after the ANOVA F-test rejects H₀ of equal means.
No MCQs match this filter.Is filter mein koi MCQ nahi.
Write down the test statistic when chi-square goodness of fit test is performed.
χ² = Σ (oi − ei)²/ei, where oi are observed and ei expected frequencies; it has approximately a χ² distribution with k − 1 − r degrees of freedom (k classes, r parameters estimated from the data).
Define LSD test.
The least significant difference (LSD) test is used after ANOVA rejects H0 of equal means. It computes the smallest difference between two treatment means that is significant, LSD = t(α/2, v)√(2MSE/r), where v is the error degrees of freedom and r the number of replications; any pair of means whose absolute difference exceeds LSD is declared significantly different.
Elaborate the Least Significant Difference (LSD) test.
After ANOVA rejects equality of means, LSD = t(α/2, error df)√(2MSE/r) is computed; each pair of treatment means whose absolute difference exceeds LSD is significantly different.
Explain the Chi-square test of goodness of fit.
It tests whether observed frequencies agree with expected frequencies from a hypothesised distribution, using χ² = Σ(o − e)²/e with k − 1 − m degrees of freedom (k classes, m estimated parameters); a large χ² leads to rejecting the fit.
If there are K treatments and R rows in a Randomized Complete Block Design then calculate the total number of experimental units used.
In an RCBD every treatment appears exactly once in every block (row). With K treatments and R blocks the total number of experimental units is n = K × R = KR (for example, 4 treatments in 5 blocks need 20 units).
While applying the chi-square goodness of fit test, if an expected frequency in any category is less than 5, then what we do to solve this problem.
Combine (pool) that category with an adjacent category (and add their observed frequencies too) until every expected frequency is at least 5. The degrees of freedom are then reduced, since they are computed from the new number of categories: ν = k − 1 − (number of estimated parameters).
Formulate the hypothesis in case of goodness of fit test.
H0: the data follow the specified (hypothesised) distribution, i.e. observed frequencies agree with the expected frequencies. H1: the data do not follow the specified distribution. Test with χ² = Σ(o − e)²/e on (k − 1 − number of estimated parameters) degrees of freedom.
If we have RCBD with MSE = 3.19, number of treatments = 4, number of blocks = 5, then find the value of LSD (least significant difference) for treatments by using α = 0.05 and error degrees of freedom is 12.
LSD = t(0.025, 12) √(2MSE/r) = 2.179 × √(2 × 3.19/5) = 2.179 × √1.276 = 2.179 × 1.1296 = 2.46. Any two treatment means differing by more than 2.46 are significantly different.
The following data was obtained for a randomized block design involving five treatments and three blocks: SST = 430, SSTR = 310, SSB = 85. Set up the ANOVA table.
SSE = 430 − 310 − 85 = 35. Treatments: df 4, SS 310, MS 77.5, F = 77.5/4.375 = 17.71. Blocks: df 2, SS 85, MS 42.5, F = 42.5/4.375 = 9.71. Error: df (5−1)(3−1) = 8, SS 35, MS 4.375. Total: df 14, SS 430.
Write down the testing procedure in case of goodness of fit test.
(1) State H₀: the data follow the specified distribution (the observed frequencies agree with the expected ones); H₁: the data do not follow it. (2) Choose the level of significance α. (3) Compute expected frequencies eᵢ = n·pᵢ from the hypothesised distribution (combine classes so each eᵢ is at least 5). (4) Test statistic χ² = Σ (oᵢ − eᵢ)²/eᵢ, which follows approximately a chi-square distribution with ν = k − 1 − r degrees of freedom (k classes, r parameters estimated from the data). (5) Critical region: reject H₀ if computed χ² ≥ χ²α(ν) (right-tailed test). (6) Compute χ² and draw the conclusion: if it falls in the critical region reject H₀ (poor fit), otherwise do not reject (good fit).
A personal manager is interested in trying to determine whether absenteeism is greater on some specific day of the week or not? His records for the past year show the following sample distributions. Day of the week: Monday, Tuesday, Wednesday, Thursday, Friday; No. of absentees: 66, 57, 54, 48, 75. Test goodness of fit. Where test statistic chi-square = Σ(oᵢ − eᵢ)²/eᵢ = 7.50
1) H₀: absenteeism is equally distributed over the five days (uniform); H₁: it is not. 2) α = 0.05 (not given; usual level assumed). 3) Total = 66 + 57 + 54 + 48 + 75 = 300, so eᵢ = 300/5 = 60 for each day. 4) χ² = Σ(oᵢ − eᵢ)²/eᵢ = (36 + 9 + 36 + 144 + 225)/60 = 450/60 = 7.50 (matches the given value). 5) df = k − 1 = 5 − 1 = 4; critical value χ²₀.₀₅(₄) = 9.488. 6) Since 7.50 < 9.488, do not reject H₀: there is no significant evidence that absenteeism is greater on any particular day.